A cartridge filter is built from five core parts: filter media, an inner core, an outer support cage, end caps, and seals such as O-rings or gaskets. Each one affects flow, strength, chemical compatibility and leak-free sealing. Knowing how the cartridge filter components work together helps you write a purchase specification that gets the right part the first time, instead of discovering a mismatch after installation.
What Are the Main Components of a Cartridge Filter?
The main components are the media, core, cage, end caps and seals, and the fluid passes through them in a set order. Liquid enters the housing, flows through the outer cage, passes through the media where particles are captured, and exits through the perforated core. The end caps hold everything together and direct the flow, and the seals stop liquid from bypassing the media.
One manufacturer’s technical article lists a more detailed breakdown with supporting layers, inner and outer cages, and a core, and it stresses that the failure point is rarely the membrane itself. That is a useful reminder for buyers: the media gets most of the attention, but the parts around it often decide whether the cartridge performs.
Filter Media
Filter media is the layer that actually captures contaminants, and its type and rating define what the cartridge removes. Everything else in the cartridge exists to support, seal or protect it.
Pleated, Melt-Blown and Wound Media
The media format changes how the cartridge behaves in service:
- Pleated media folds a sheet into pleats to create a large surface area in a small cartridge. Membrane materials such as PES, PTFE, PVDF and nylon are common choices where fine, precise filtration is needed.
- Melt-blown depth media is made from polypropylene microfibers. One datasheet describes a pleated depth cartridge with melt-blown polypropylene microfiber media and non-woven or mesh polypropylene support layers. Depth media captures particles throughout its thickness, which suits fluids with heavier or varied particle loads.
- String-wound and other depth formats are common for general sediment removal, usually at a lower cost per cartridge.
As a rule of thumb, surface-type pleated media suits tight, repeatable filtration, while depth media suits higher dirt loads. Your fluid, particle size distribution and acceptable cost per change should drive the choice.
Nominal vs Absolute Micron Ratings
A micron rating states the particle size the cartridge is designed to remove, but the meaning of that rating depends on how the manufacturer defines it. A nominal rating means the cartridge removes a stated percentage of particles at that size, while an absolute rating means a much higher, tightly defined removal at that size. Manufacturer literature for depth cartridges often lists absolute-rated media with a gradient pore structure that gives high flow rates. When comparing quotes, confirm which kind of rating each supplier is using, because two cartridges both labeled “5 micron” may not perform the same.
Core, Support Layers and Outer Cage
The core and cage give the cartridge its mechanical strength, so it keeps its shape under pressure. The perforated inner core carries filtered fluid out and stops the media from collapsing inward under differential pressure. The outer cage protects the media from handling damage and keeps pleats from flexing outward.
Thin support layers, typically non-woven or mesh, sit on each side of pleated media to protect it. Polypropylene is a common material for all of these parts. Several datasheets list the cage, core and end caps as polypropylene, even where the media is PTFE. Stainless steel cores or reinforcement rings are used when added strength or higher temperature capability is needed. One high-temperature option from a manufacturer is rated to a maximum of 200°F (93.3°C), available only in 222 or 226 with fin or flat end caps. That limit comes from one supplier’s product line, so check the rating of the exact cartridge you plan to buy.
End Caps and End Configurations
End caps seal and hold each end of the cartridge, and they determine how the cartridge fits into the housing. They are bonded to the media pack so that all fluid must go through the media. One technical source describes them as securing each end so that fluid must pass through the filtering media.
DOE vs SOE
DOE means double open end and SOE means single open end:
- DOE cartridges are open at both ends and are usually sealed with gaskets or flat seals against the housing. They stack end to end in multi-element housings.
- SOE cartridges are open at one end and closed or capped at the other, and they typically seal with O-rings at the open end.
222, 226, Fin and Flat
The 222 and 226 numbers refer to standard O-ring sizes, and the end style is usually a fin (with locking tabs) or a flat cap. Manufacturer ordering codes list combinations such as 222 with a fin end, 222 with a flat end, 226 with a fin end, and 226 with a flat end, along with internal O-ring styles. The details are not interchangeable: a cartridge that fits one housing’s seating style may leak in another. Always match the code to the housing’s adapter, not just to the cartridge length and diameter.
O-Rings and Gaskets
O-rings and gaskets prevent bypass, and their material often decides chemical compatibility. They form a tight seal between the cartridge and the housing, preventing leakage and forcing fluid through the media. A leaking seal lets unfiltered fluid pass straight through, however good the media is.
Common elastomers include Buna-N, EPDM (also called EPR), silicone and Viton, with encapsulated options for aggressive chemicals. Product datasheets list choices such as Buna-N, EPR, silicone, Viton and PFA-encapsulated Viton. The right option depends on fluid chemistry and temperature. As a general guide, check compatibility charts for the specific fluid and never assume that the media material and the seal material tolerate the same chemicals.
How the Components Are Joined
Joining method affects both purity and durability. Traditionally, end caps are attached with adhesives or potting compounds such as resins, epoxies and polyurethanes, or by thermal or melt bonding. Thermal bonding fuses polypropylene parts directly, with no adhesive, which reduces the risk of extractables. One manufacturer describes media and support structure that are thermally bonded to the end caps, giving an integral cartridge with good chemical compatibility and minimal extractables. Another sealing approach uses double O-rings and highlights the absence of epoxies or glues that could contaminate fluid streams.
If you filter food, beverage, pharmaceutical or high-purity process fluids, ask how the end caps are attached and what the materials are certified for.
Material Selection
Match materials to the fluid, temperature and pressure, and verify each component separately. A simple comparison helps:
| Component | Common materials | Main selection factor |
|---|---|---|
| Media | Polypropylene, PES, PTFE, PVDF, nylon | Particle size, fluid compatibility, retention |
| Core and cage | Polypropylene, stainless steel | Pressure, temperature, strength |
| End caps | Polypropylene | Housing fit, bonding method |
| Seals | Buna-N, EPDM, silicone, Viton, encapsulated | Chemical resistance, temperature |
Buyer’s Checklist
Use this list before you order or compare quotes:
- Fluid and application. Water, chemicals, solvents, food or process fluids each narrow the material choices.
- Micron rating and type. Confirm nominal or absolute, and the media format.
- Dimensions. Check outer diameter and length against the housing.
- End configuration. Match DOE or SOE, 222 or 226, fin or flat to the housing.
- Seal material. Verify compatibility with the fluid and operating temperature.
- Operating limits. Confirm maximum temperature and differential pressure for the exact cartridge.
- Construction method. Ask about thermal bonding or adhesives, especially for sensitive fluids.
- Documentation. Request material certifications and test data that suit your industry.
- Replacement interval. Ask for the recommended change-out differential pressure.
Common Specification Mistakes
Most ordering errors are mismatches, not defects. Typical examples include:
- ordering by micron rating and length alone, and ignoring end configuration;
- choosing the right media but the wrong O-ring material;
- confusing nominal and absolute ratings between suppliers;
- ignoring temperature limits of cages, cores and seals;
- comparing price per cartridge without considering service life.
If a replacement cartridge does not seat or seal properly, the cause is usually a small detail such as a 222 vs 226 mismatch or a gasket style, not the filtration itself.
Next Step
Start by writing down your fluid, temperature, pressure, housing model and target micron rating, then compare cartridges component by component. If you want help matching a cartridge to your housing or checking a specification.
FAQs
Q1. What are the main parts of a filter cartridge?
A. The main parts are the filter media, inner core, outer cage, end caps, and seals such as O-rings or gaskets. Supporting layers sit between the media and the cages.
Q2. What does DOE mean on a filter cartridge?
A. DOE means double open end. The cartridge is open at both ends and typically seals with gaskets, while single open end (SOE) designs seal with O-rings.
Q3. What is the difference between 222 and 226 cartridges?
A. They refer to different standard O-ring sizes and fit different housing adapters. They are not interchangeable, so match the code to your housing.
Q4. Which O-ring material should I choose?
A. It depends on the fluid and temperature. Common options are Buna-N, EPDM, silicone and Viton, and you should check a compatibility chart for your specific chemical.
Q5. Are the end caps glued or welded?
A. Both methods exist. Some cartridges use adhesives or potting compounds, while others use thermal bonding with no adhesive, which can reduce extractables.
Q6. Is a nominal or absolute rating better?
A. Absolute ratings indicate a more tightly defined removal at the stated size. Choose based on how critical the filtration is and how each supplier defines its rating.